Twitter IconFacebook IconBathtubs and Sinks-Repairing and Refinishing in Medford

Directions For Painting Bathtub Sinks Tile With Spray On Kit

Please Print These Directions

Warning

PROVIDE ADEQUATE VENTILATION. USE LATEX GLOVES WHEN HANDLING BATHTUB REFINISHING COATINGS AND BONDING SPRAY. FOLLOW MANUFACTURES DIRECTIONS AND AVOID BREATHING VAPORS. IF YOU OR ANYONE IN YOUR HOME HAS RESPIRATORY HEALTH PROBLEMS OR ASTHMA, DO NOT USE THIS PRODUCT. EXTINGUISH ALL IGNITION SOURCES. DO NOT SMOKE WHILE USING. FLAMMABLE.

COLOR MATCHES OF YOUR EXISTING FIXTURE MAY NOT BE POSSIBLE. IN THIS CASE, REFINISH THE ENTIRE FIXTURE.

KITCHEN SINKS RECEIVE A LOT OF ABUSE FROM POTS, PANS, SILVERWARE AND OTHER ITEMS DROPPED IN THEM. REAPPLICATION MAY BE NEEDED IF COATING IS CHIPPED, OR SCRATCHING OCCURS. DO NOT USE ABRASIVE CLEANSERS OR PADS. CLEAN WITH A NON BLEACH NONE ABRASIVE CLEANSER.

DIRECTIONS

STEP 1 – PREPARING THE FIXTURE (Refinishing Bathtubs, sinks, tile, fiberglass showers, countertops, cultured marble)
A. Use products at room temperatures above 60 degrees only. The preparation of the fixture is the most important step in the refinishing process. Follow directions completely.
B. Surface must be clean, dry and free from rust. Remove caulking with a razor blade or putty knife. Remove soap scum, grease, wax, etc by wiping the fixture with Acetone purchased from your local hardware store. All fixtures, tile, and especially fiberglass fixtures must be sanded with 80 grit sandpaper to remove paint droppings, silicone caulking film, and other impurities prior to continuing. Fiberglass fixtures must be thoroughly sanded to roughen the surface prior to spraying on the bonding agent. (Exceptions are formica countertops, cultured marble and plastics. These surfaces require a light sanding with 320 grit sandpaper)
C. Remove any rust with a wire brush.

D. Chip or Crack Repairs In Sinks, Bathtubs, Tile, Cultured Marble and Fiberglass. If chips, cracks or dings are present. These must be repaired prior to refinishing. Repair kits, with easy to follow directions are available from our Super Store. After repairs are made, remove any left over debris and wipe the repaired area lightly with a small amount of Acetone on a paper towel. If you are just touching up the fixture, spray a light coat of Bonding Agent to the repair area only, wait 5 minutes and then follow the directions in step #3. If refinishing the complete fixture proceed to Step #2

* REMOVE ANY SILICONE OR OTHER TYPES OF CAULKING FROM THE FIXTURE COMPLETELY

STEP 2 – Applying Masking Tape and Spraying on Bonding Agent

Make sure fixture is dry and free of debris. Mask plumbing fixtures and surrounding areas with masking tape and paper if needed. Be sure to mask the drain areas of bathtubs and sinks. Cut excess tape from drains using a razor knife. Wipe the entire fixture with Acetone prior to applying the bonding agent. Allow Acetone to evaporate. Spray a light coat of Bonding Agent to the entire surface you are refinishing. Hold can 6″ to 12 ” away from fixture and spray in a sweeping motion, left to right, starting from one end of the fixture to the next. Be sure to overlap each stroke 50% and avoid any runs. On Sinks, start at the drain, and work your way out of the sink to the edges. For bathtubs, start at drain area, then cover the bottom of the bathtub, next the sides of the tub, and finally the top lip and the front of the bathtub last. Wait 5 -15 MINUTES THEN APPLY THE REFINISHER COATING PAINT AS DIRECTED IN STEP #3. Caution – Do not let Bonding Agent sit more than 60 minutes before applying the Refinisher Coating. IF you do, it will have to be removed with Acetone, and Step #2 will have to be repeated.

STEP 3 – Applying The Bathtub Refinishing Spray On Paint Coating ( Paint Color) Temperature and humidity may extend drying times.

A. Mask off plumbing fixtures, walls, or any other surfaces not being refinished.
B. Make sure arrow on spray can is facing away from you.. Hold the can about 6-8 inches from the surface, spray with short stroking motions. Do not try to apply coating all at once. Apply 3-light coats and finish with a good, wet, shiny coat waiting 5 minutes between each coat.
C. Avoid runs, If you do get any runs, wipe the spray off with a paper towel lightly saturated with Acetone. Let surface dry. Sand if needed, and remove debris with a paper towel, lightly saturated with Acetone .
D. To avoid splatters, clean spray nozzle buildup with a clean cloth, as needed. If the nozzle clogs, hold the can upside-down and spray to clean out spray nozzle.
E. Overspray can be removed from surfaces using a paper towel lightly saturated with Acetone. When finished, remove masking tape and paper. Do not allow fixture to dry with masking tape or paper left on it. Be careful not to get debris on wet coating. Allow to Dry 24-48 hours – DO NOT USE THE FIXTURE OR ALLOW THE SPRAYED AREA TO GET WET FOR 24-48 HOURS. The coating will harden in about 30 minutes please do not touch.

Note For Appliances: Refrigerators, stoves, dishwashers, range hoods, microwaves and washer / dryers only require cleaning and light sanding with 320 grit sand paper prior to masking off the appliance and following step 2 and 3 below (Application of bonding agent and painting). Great for touchups and complete painting of appliances. DO NOT USE ON COMPLETE COOKING AREA OF STOVES, OR ON VENTING AREA OF SELF CLEANING OVEN DOORS. TOUCH UPS ON THESE AREAS ARE O.K. CHIPS CAN BE REPAIRED WITH OUR PORCELAIN REPAIR KITS.

CARE AND CLEANING

Never clean fixtures with abrasive cleanser, or scrub pads. Do not use bleach or drain cleaners. Do not use suction type bath mats in bathtubs, all of these will damage the finish. Shelf life of product is 1 year. Keep out of reach of children.

USE THESE PRODUCTS AT YOUR OWN RISK.
The Bathtub Refinishing Referral Network will not be liability for incidental or consequential damages, arising from the use, or misuse of these products. Any claims regarding these products must be directed to the manufacturer. Product received damaged during shipment must be reported to the shipping company within 24 hours of receipt of damaged goods and the Bathtub Refinishing Referral Network must be notified at sales@refinishingonline.com .

Returns: Any item returned due to damage in shipping or a defective item, must receive an Identification tag, prior to shipping the item back to the supplier. Tag is only available by emailing the Bathtub Refinishing Referral Network at the above email address. We must be contacted within 24 hours of receiving a damaged or defective item. No item will be accepted without an ID tag. Refunds will include replacement of the damaged or defective product only and are provided from the manufacturer.

This product is dangerous if misused. The customer or enduser(s) assume full responsibility for its proper use and application, as outlined in these installation instructions. Material Safety Data Sheets (MSDS) are available upon request –contact: sales@refinishingonline.com .