|
Warning
PROVIDE ADEQUATE VENTILATION. USE LATEX GLOVES WHEN HANDLING COATINGS AND
PRIMERS. FOLLOW MANUFACTURES DIRECTIONS AND AVOID BREATHING VAPORS. IF YOU
OR ANYONE IN YOUR HOME HAS RESPIRATORY HEALTH PROBLEMS OR ASTHMA, DO NOT
USE THIS PRODUCT. EXTINGUISH ALL IGNITION SOURCES. DO NOT SMOKE WHILE
USING. FLAMMABLE.
COLOR MATCHES OF YOUR
EXISTING FIXTURE MAY BE ACCOMPLISHED WITH ONE OF OUR REPAIR KITS.
REPAIRS Must be
completed prior to using this product. Chips, cracks, cuts, peeling paint,
holes or other damage can be repaired by using one of our repair kits.
TOOLS NEEDED For
A Better Finish Use Foam Type Rollers And Brushes, Paint Tray, Acetone, 1
Sheet Of 100 Grit Sand Paper, Pair Of Disposable Gloves, Masking Paper, 1
Inch Roll Of Tape.
DIRECTIONS
STEP 1 - Preparing The Countertop
A. Use products at room temperatures above 60 degrees only. The
preparation of the fixture is the most important step in the refinishing
process. Follow directions completely.
B. Surface must be clean, dry and free from rust. Remove caulking
with a razor blade or putty knife. Remove soap scum, grease, wax, etc by
wiping the fixture with Acetone purchased from your local hardware store.
Laminates, cultured marble and Corian surfaces must be sanded with 80
grit sandpaper to rough up the surface and to remove paint droppings, excess
caulking or other material that is on the surface. Ceramic tile does not
require sanding, but be sure to remove foreign material from the tiles. The
grout is refinished along with the tiles.
D. Chip or Crack
Repairs If chips, cracks or dings are present. These must be repaired
prior to refinishing. Repair kits, with easy to follow directions are
available from our Super Store. After repairs are made, remove any left over
debris and wipe the repaired area lightly with a small amount of Acetone on
a paper towel.
* REMOVE ANY SILICONE OR OTHER TYPES OF
CAULKING FROM THE FIXTURE COMPLETELY
STEP 2 – Applying Masking Tape and
Primer
Make sure fixture is dry and
free of debris. Mask plumbing fixtures, sinks and surrounding areas with
masking tape and paper if needed. Once sanding is completed, wipe the entire
fixture with Acetone prior to applying the primer. Allow Acetone to
evaporate completely. Primer - Apply the primer using a dense foam
roller. Use light coat only, allowing the primer to dry to the touch before
applying the next coat. One light coat of primer is all that is required.
Allow primer to dry for 24 hours.
STEP 3 – Applying
The Brush-On Color Coating
A. Mask off sink and walls, or any other surfaces not being
refinished.
B. Mix paint thoroughly. . Do not try to apply coating all at once.
Apply one light coat and finish with a good, wet, shiny coat waiting for
the coating to dry to the touch prior to applying each coat..
C. Avoid runs, If you do get any runs, wipe the paint off with a
paper towel lightly saturated with acetone.
D. When finished, remove masking tape and paper. Do not allow fixture
to dry with masking tape or paper left on it. Be careful not to get debris
on wet coating. Allow to Dry 24-48 hours depending on temperature and
humidity – DO NOT USE THE FIXTURE OR ALLOW THE PAINTED AREA TO GET WET FOR
24-48 HOURS. DO NOT APPLY FANS OR HEAT TO TRY AND SPEED UP DRYING TIME THIS
ACTUALLY DELAYS DRYING TIMES.
Clean Up with paint
thinner or dispose of brushes, rollers and other materials properly. Do not
allow children in the work area.
CARE AND CLEANING
Never clean fixtures with abrasive cleanser, or scrub pads. Do not use
bleach or drain cleaners. Shelf life of product is approximately 1 year.
Keep out of reach of children.
USE THESE PRODUCTS AT YOUR
OWN RISK.
The Bathtub Refinishing Referral Network will not be liability for
incidental or consequential damages, arising from the use, or misuse of
these products. Any claims regarding these products must be directed to the
manufacturer. Product received damaged during shipment must be reported to
the shipping company within 24 hours of receipt of damaged goods and the
Bathtub Refinishing Referral Network must be notified at
sales@refinishingonline.com .
Returns: Any item
returned due to damage in shipping or a defective item, must receive an
Identification tag, prior to shipping the item back to the supplier. Tag is
only available by emailing the Bathtub Refinishing Referral Network at the
above email address. We must be contacted within 24 hours of receiving a
damaged or defective item. No item will be accepted without an ID tag.
Refunds will include replacement of the damaged or defective product only
and are provided from the manufacturer.
This product is dangerous if misused. The customer or enduser(s) assume
full responsibility for its proper use and application, as outlined in these
installation instructions. Material Safety Data Sheets (MSDS) are available
upon request –contact:
sales@refinishingonline.com .
|
